ExpEYES/C2/Panel-connections-and-software-interface/English
| Visual Cue | Narration |
| Slide Number 1
Title Slide |
Hello everyone.
Welcome to this tutorial on Panel connections and Software interface |
| Slide Number 2+3
Learning Objectives We will learn about,
|
In this tutorial, we will learn about:
We will also learn to demonstrate:
|
| Slide Number 4
System Requirement
|
Here I am using,
|
| Slide Number 5
Pre-requisties
For relevant tutorials, visit our website. www.spoken-tutorial.org |
To follow this tutorial, you should be familiar with:
ExpEYES Junior interface. If not, for relevant tutorials, please visit our website. |
| Let's discuss about the utilities of ExpEYES Junior device. | |
| Slide Number 6
Utility of ExpEYES Junior.
|
Device can be used to carry out experiments in:
|
| Slide Number 7
Fields
|
It can be used in fields such as:
|
| Let's begin with terminals on the top Panel. | |
| Point to ground(GND) terminals. | Panel has four ground (GND) terminals.
At these terminals the voltage is zero volt(0V). Voltage measured at other input terminals, is with reference to ground(GND) terminals. |
| Point to terminals A1 and A2 | Input terminals A1 and A2 can measure voltage between -5V to +5V. |
| Point to terminal IN1 and IN2. | On the left, IN1 and IN2 terminals can measure voltage between 0 to 5V.
'IN1 also measures capacitance up to 5000pF(pico farads), with good accuracy. |
| Point to PVS | PVS is Programmable voltage source.
It is used to deliver voltages
|
| Point to SINE | SINE delivers a constant frequency around 150 Hz, at an amplitude around 4volts. |
| Point t to SEN | SEN is mainly used for connective sensor elements like
It is a voltage measuring terminal with an internal 5.1k resistor connected to 5 volts. |
| Point to SQR1 and SQR2 terminals | SQR1 and SQR2 terminals can generate
|
| Point to OD1 | OD1 produces a digital output as 0V or 5V, under Software control. |
| Point to MIC | MIC captures sound from an external sound source. |
| Point to CCS | CCS means Constant Current Source.
It gives
since voltage should be kept below 4 volts. |
| Point to IN->OUT | Inverting amplifier (IN->OUT) is used to amplify external voltages.
It may be used to amplify external condenser or mic output. |
| Along with the device, some accessories are provided. | |
| Point to all the accessories one by one. | Accessories list include:
|
| Move the cursor on to the software interface. | This is a graphical user interface(GUI) of ExpEYES Junior.
GUI is known as Plot window. |
| Point to all the input terminals | On the left side of the Plot window, we have input terminals:
A1, A2, IN1, IN2, SEN, SQ1 and SQ2. |
| Point to ATR, WHI and others are trigger sources. | ATR, WHI and others trigger sources are used to fix the waveform.
|
| Point to CH1, CH2, CH3, CH4.
Cursor on the channels. |
CH1, CH2, CH3, CH4 are plotting channels with sliders.
|
| Point to A1, Click on A1 and drag to CH1.
Point to information in the box below. |
Click on A1 and drag to CH1.
|
| Point to A2, Click on A2 and drag to CH2.
Point to information in the box below. |
Click on A2 and drag to CH2.
|
| Point to FIT. | Drag channel CH2 to FIT.
|
| Point to NML | Drag CH2 to NML.
|
| Point to msec/div (milli second per division) | msec/div(milli second/division) represents time axis. |
| Point to Volt/div | Volt/div represents volt axis. |
| Point to Trig level | Trig level is a trigger controller. |
| Point To DEL.
Click on CH2 and drag to DEL. |
Click on CH2 and drag to DEL.
It removes CH2. |
| Point to DEL.
Click on CH1 and drag to DEL. |
Click on CH1 and drag to DEL.
It disables the display of CH1. |
| Point to FTR. | FTR generates Fourier spectrum of the wave. |
| Point to Setting Squarewaves | Under Setting Squarewaves we have a number of input and check boxes. |
| Point to Frequency input box. | In this input box we can change the Frequency of the wave in Hertz, |
| Point to phase difference input box. | This is to change phase difference, dphi in percentage(%). |
| Point to Set PVS= | In Set PVS= input box
we can enter the desired voltage value between 0 to 5V. Press Enter to set the value. |
| Point to the check boxes, SQR1, SQR2 and BOTH. Point to the slider. | SQR1, SQR2 and BOTH check boxes are used to activate the frequency.
Frequency can be changed using the slider. |
| Point to Set State OD1 and CCS | Set State check boxes are used to control OD1 and CCS. |
| Point to Measure C on IN1. | Measure C on IN1 button is used to measure Capacitance. |
| Point to Measure R on SEN | Measure R on SEN button is used to measure Resistance |
| Point to command window. | Below the buttons we have a command window to type Python code.
We will discuss about Python code in upcoming tutorials. |
| Point to Save Traces to button. | Save Traces to button to save traces as .txt files |
| Point to LOOP check box, SCAN and XMG buttons | We will discuss about LOOP check box, SCAN and XMG buttons in later tutorials. |
| Point to EXPERIMENTS button.
Point to Quit button. |
EXPERIMENTS button displays list of experiments.
Quit button is used to close the window. |
| Now I will demonstrate Ohm's law using the device and its interface. | |
Slide Number 8
|
In this experiment we will show:
|
| Point to PVS
Point to IN1. Point to the Circuit diagram. |
The device is connected to the system.
In this experiment PVS is connected to IN1 through 2.2KΩ(kilo ohms) resistance. IN1 is connected to ground(GND) through 1KΩ(kilo ohms). This is the circuit diagram for the connection. |
| R1=1KΩ
R2=2.2K Ω |
Open the software interface.
In the Plot window click on IN1 to measure the voltage. |
| For PVS=1V, IN1 value is 0.309 V.
For PVS=2V, IN1 value is 0.619V For PVS=3V, IN1 value is 0.928V |
For PVS=1 Volt, the corresponding value of IN1 is 0.309 Volt.
For PVS=2V, IN1 value is 0.619V For PVS=3V, IN1 value is 0.928V. |
| Slide Number 9
Assignment
|
As an assignment,
|
| Let us perform an experiment to check the effective resistance in series combination. | |
| Slide Number 10
Voltage when resistors are connected in series. |
In this experiment we will show the voltage when resistors are connected in series. |
| Show the experimental arrangement. | In this experiment
|
| Point to the Plot window
Show the Circuit diagram. |
On the Plot window select the CCS check box.
Click on IN1 to show the voltage. This is the circuit diagram for the connection. |
| For 1 KΩ, IN1=0.979V | When 1 KΩ(kilo ohms) resistor is connected to CCS and GND, measured voltage is 0.979V. |
| For 560 Ω, IN1=0.543V | Likewise, for 560 Ω(ohms) resistance, measured voltage is 0.543V. |
| For 1 KΩ and 560Ω, IN1=1.524V | For a series combination of 1 KΩ (kilo ohms)and 560Ω(ohms) resistances, measured voltage is 1.524V'. |
| Let us perform an experiment to check the effective resistance in parallel combination | |
| Slide Number 11
Voltage when resistors are connected in parallel. |
In this experiment we will show the voltage when resistors are connected in parallel. |
| Show the circuit diagram | In this experiment IN1 is connected to CCS. CCS is connected to ground(GND) through a resistor.
This is the circuit diagram for the connection. |
| Point to Plot window | On the Plot window select the CCS check box.
Click on IN1 to show the voltage. |
| Experiments is carried out with 1000Ω(ohms) resistor.
Parallel combination of two 1000 Ω(ohms) resistors. |
The experiment is first carried out with 1000Ω(ohms) resistor
then with parallel combination of two 1000 Ω(ohms) resistors. |
| for 1000 Ω, IN1=0.952V | This is the circuit diagram for 1000 Ω(ohm) resistance in parallel combination.
The measured value of IN1 is 0.952V. |
| for two 1000Ω, IN1=0.474V | This is the circuit diagram for parallel combination of two 1000 Ω(ohm) resistors.
The measured value of IN1 is 0.474V. |
| Experiments is carried out with 2.2K Ω(kilo ohms) resistor
Parallel combination of two 2.2 KΩ(kilo ohms) resistors. |
Again the experiment is carried out
|
| for 2.2K Ω, IN1=2.132V | This is the circuit diagram for 2.2K Ω(kilo ohms), resistance.
The measured value of IN1 is 2.132V |
| for two 2.2KΩ, IN1=1.063V | This is the circuit diagram for parallel combination of two 2.2KΩ(kilo ohms) resistance.
The measured value of IN1 is 1.063V |
| Let's summarize. | |
| Slide Number 12
we have learnt,
We have also learnt to demonstrate:
|
In this tutorial we have learnt,
We have also learnt to demonstrate:
|
| Slide Number 13
Assignment |
As an assignment,
Measure the effective resistance using a combination of Series and Parallel resistors. |
| Slide Number 14
Acknowledgement Watch the video available at http://spoken-tutorial.org /What is a Spoken Tutorial It summarises the Spoken Tutorial project. If you do not have good bandwidth, you can download and watch it. |
This video summarizes the Spoken Tutorial project
If you do not have good bandwidth, you can download and watch it. |
| Slide Number 15
The Spoken Tutorial Project Team Conducts workshops using spoken tutorials Gives certificates to those who pass an online test For more details, please write to contact@spoken-tutorial.org |
We conduct workshops using Spoken Tutorials and give certificates.
Please contact us. |
| Slide number 16
Spoken Tutorial Project is a part of the Talk to a Teacher project It is supported by the National Mission on Education through ICT, MHRD, Government of India More information on this Mission is available at http://spoken-tutorial.org/NMEICT-Intro |
The Spoken Tutorial Project is funded by NMEICT, MHRD Government of India |
| This tutorial is contributed by Kaushik Datta and Madhuri Ganapathi.
This is Sakina Sidhwa. Thank you for joining. |
