Single-Board-Heater-System/C2/Connecting-SBHS-to-Computer/English-timed
From Script | Spoken-Tutorial
| |
|
|---|---|
| 00:01 | Welcome to the Spoken tutorial on “Connecting SBHS to Computer”. |
| 00:05 | We would call Single Board Heater System as "SBHS" in this tutorial. |
| 00:12 | In this spoken tutorial, we will learn to set up physical communication between SBHS and computer to install USB driver. |
| 00:21 | To work with SBHS, we would require SBHS with power cable and USB/RS232 communication cable. |
| 00:35 | On a Windows machine, we would also require FTDI Virtual Com Port USB driver corresponding to the OS on your computer. |
| 00:44 | You may download it from: [www.ftdichip.com/Drivers/VCP.htm] |
| 00:54 | Let me show you this website. |
| 00:59 | On this website, scroll down and choose the driver file corresponding to your OS. |
| 01:09 | I have downloaded 32 bit 2.08.14 driver file for Windows. |
| 01:22 | The single board heater system and your computer can be connected using a USB cable or RS232 cable. |
| 01:30 | Identify the corresponding ports on your computer and SBHS. |
| 01:35 | Here is an image of the USB port, you will find, on the back panel of a computer. |
| 01:44 | A Serial port on the computer back panel, |
| 01:49 | USB and Serial port on the SBHS. |
| 01:54 | Please note that before deciding to use RS232 cable, confirm the availability of RS232 port on your computer. |
| 02:04 | After you choose between USB and the serial cable 232, you have to do some corresponding jumper settings. |
| 02:12 | A jumper is just a small black color connector. |
| 02:17 | A pair of these is shown here; each jumper can connect two terminals. |
| 02:26 | The connectors on SBHS with both the jumpers removed is as shown in the figure. |
| 02:33 | Here we can see that there are three terminals on either side. |
| 02:39 | We can also see the labels USB and RS232 being printed besides these connectors on the PCB. |
| 02:50 | The center terminal on either side is the common terminal. |
| 02:55 | Take a jumper and connect the common terminal of one side and the terminal closer to the label USB of the same side. |
| 03:06 | Take another jumper and do the same thing for the other side. |
| 03:11 | This is how you set the jumpers to choose the USB port for communication. |
| 03:17 | Similarly, one can put both the jumpers on common terminal and the terminal towards the label RS232 to choose the RS232 port for communication. |
| 03:29 | I have configured the jumper settings to choose USB port as shown. |
| 03:38 | After the jumper setting is done, connect the power cable to a 3 pin, 230 Volt AC house hold socket and the SBHS. |
| 03:51 | Switch the mains power ON. There may or may not be an ON/OFF switch on the SMPS of the SBHS, below the power cabel connector. |
| 04:06 | If the device is successfully powered, the display should turn ON. |
| 04:12 | Here is an image of the display on SBHS. |
| 04:16 | Note that what is actually seen on the display may vary from what is shown. But, it should certainly not be blank. |
| 04:25 | After powering ON the SBHS, connect the appropriate USB/RS232 cable to the SBHS and the computer. |
| 04:33 | Here is an illustration of USB cable connected to SBHS and the laptop. |
| 04:42 | Always make sure that you first power ON the device and then connect the USB/RS232 cable. |
| 04:52 | Next we will see driver installation. |
| 04:56 | Recall that the FTDI VCP USB driver was downloaded earlier from ftdichip.com. |
| 05:04 | You can also find here a guide for driver installation. Download the guide from: www.ftdichip.com |
| 05:13 | Let us go to this website. |
| 05:22 | In the left panel, click on “Drivers”. |
| 05:27 | In the dropdown menu, choose “VCP Drivers”. |
| 05:33 | Click on the “Installation Guides” link on the web page. |
| 05:41 | Choose the required operating system document. |
| 05:46 | Since I am using Windows 7 operating system, I have refered to “Windows 7 Installation Guide”. |
| 05:55 | You may choose the Operating System Guide according to your requirement . |
| 06:00 | This guide has detailed step by step instructions for driver installation. |
| 06:07 | Let me show you the Windows 7 PDF guide file. |
| 06:14 | Follow the steps as explained in this guide and install the driver. |
| 06:21 | The typical steps involved are: |
| 06:28 | Opening the device manager |
| 06:40 | Locating the USB port |
| 06:51 | Putting the driver path |
| 07:03 | And, repeating the steps once more. |
| 07:08 | Once the driver is successfully installed, |
| 07:12 | you should get the device listed under COM & LPT. |
| 07:20 | Let me show you this over here. |
| 07:28 | Your device should also get a COM number. |
| 07:32 | Here, for example, it is shown as "COM 3". |
| 07:45 | Now, Let us summarise what we learnt in this tutorial. |
| 07:51 | First is- connect the SBHS and computer. This involves choosing RS232/USB port, Jumper settings, powering ON the SBHS. |
| 08:05 | Second- install USB driver, downloading the installation guide, following the guide and installing the driver. |
| 08:17 | Watch the video available at http://spoken-tutorial.org/What_is_a_Spoken_Tutorial |
| 08:27 | It summarises the Spoken Tutorial project. If you do not have good bandwidth, you can download and watch it. |
| 08:37 | The Spoken Tutorial project team conducts workshops using spoken tutorials, gives certificates to those who pass an online test. |
| 08:48 | For more details, please write to: contact @spoken-tutorial.org |
| 08:56 | Spoken Tutorial project is a part of the Talk to a Teacher project. |
| 09:00 | It is supported by the National Mission on Education through ICT, MHRD, Government of India. |
| 09:07 | More information on this mission is available at http://spoken-tutorial.org/NMEICT-Intro |
| 09:18 | Thanks for joining. This is Rupak Rokade from IIT Bombay, signing off. |
