OpenPLC-version1-with-LDmicro/C3/RTO-Timer-Instruction/English

Visual Cue	Narration
Slide 1:	Welcome to the spoken tutorial on RTO timer instruction.
Slide 2: Learning Objectives Retentive Delayed turn ON (RTO) timer	In this tutorial we’ll learn about working of Retentive Delayed Turn ON timer.
Slide 3: System Requirements* Ubuntu 18.04 OS LDmicro OpenPLC V1 Mainboard 24V, 2A SMPS USBasp programmer Traffic Light module Switchboard module	To record this tutorial I am using: Ubuntu Linux 18.04 operating system LDmicro OpenPLC version1 Mainboard 24V, 2A SMPS USBasp programmer Traffic Light module and Switchboard module
Slide 4: Pre-requisites Working of a Contact and a Coil If not, please refer to the relevant tutorials from Home | spoken-tutorial.org	To follow this tutorial, you should know the working of a Contact and a Coil. If not, please refer to the relevant tutorials in this series on this website.
Slide 5: Prerequisites - Hardware setup hardware-prerequisite.jpg	Connect SMPS and USBasp to the Mainboard as shown in the picture. Keep these connections throughout this tutorial.
Open the LDmicro	Let us open LDmicro.
Insert ‘Instructions -> Insert Contact’ >> Place the cursor to the right of the contact >> Insert ‘Instructions -> Insert Coil’	Insert a Contact and a Coil as shown.
Double-click on contact >> Type switch in name box >> Click OK button	Rename the Contact as ‘switch’.
Double click on the coil >> Rename it as ‘LED1’ >> Click OK button	Then rename the Coil as ‘LED’.
Place the cursor to the right of the contact >> Click Instructions -> Timers -> Insert RTO	We will now add a Retentive Delayed turn on timer to the right of Xswitch. For that, place the cursor to the right of Xswitch. Click on Instructions then Timers and then Insert RTO.
Double-click on Tnew >> Type RTO in the name box >> Type 5000 in the delay box >> Click the OK button	Rename it as ‘RTO’ and enter the delay as 5s. Note that the name will be prefixed by T by default. Click the OK button.
	We will now check the working of this logic.
Click Simulate -> Simulation mode >> Click Simulate -> Real-time simulation	Let us turn on the simulation mode. For that, click Simulate and then on Simulation mode. Next, start real-time simulation as shown.
Highlight the state of Xswitch, YLED and TRTO in the IO list	Initially the state of Xswitch, YLED and TRTO are 0.
Double click on Xswitch	Double click on Xswitch to change the state to 1. We can observe that the state TRTO is 20ms.
Double click on Xswitch	Within 5s change the state of Xswitch back to 0.
Highlight the state of TRTO	We can observe that the state of TRTO doesn’t go to 0. Instead it shows the accumulated delay value just before Xswitch is 0.
Double click on Xswitch in the IO list Highlight the state of TRTO	Change the state of Xswitch to 1. We can observe that the timer starts. The count starts from where it was before and not from 0.
Highlight the state of TRTO and YLED	After 5s the state of YLED changes to 1 and TRTO to 4.990s
Double click on Xswitch	Now change the state of Xswitch to 0.
Highlight the state of TRTO and YLED	We can observe neither YLED nor TRTO changes its state.
	This is because the RTO timer retains its state when Xswitch turns 0.
	Thus it must be reset manually using the RESET instruction. We will now see how to RESET.
Click Simulate -> Halt Simulation >> Click Simulate -> Simulation Mode	Now, turn off the simulation mode. For that, click Simulate and then on Halt Simulation. Then click Simulate and Simulation Mode.
Click Edit -> Insert rung below	Insert a new rung below.
Place the cursor near the new rung >> Click Instructions -> Insert Contact >> Place the cursor to the right of the contact >> Click Instructions -> Insert Reset	Place a Contact and RESET instruction in the new rung as shown.
Double click on Xnew >> Type reset in the name box >> Click the OK button	Rename the Contact as ‘reset’.
Double-click reset instruction	Now double-click on RESET instruction.
Highlight the type column	Under the column Type we can find two options Timer and Counter. That means with this instruction we can reset only timer and counter variables. By default, it is set to Timers. Don’t change it.
Type RTO in the name box	The name should be the name of the timer variable that needs to be reset. So type RTO.
Click the OK button	Click the OK button.
Click Simulate -> Simulation mode >> Click Simulate -> Real-time simulation	Start real-time simulation as shown.
Double click on Xswitch	Change the state of Xswitch to 1.
Highlight the state of TRTO	After 5s the state of TRTO changes to 4.990s. Change the state of Xswitch back to 0.
Double click on Xreset	Now change the state of Xreset to 1.
Highlight the state of TRTO	We can observe the timer TRTO resets.
Click Simulate -> Halt Simulation >> Click Simulate -> Simulation Mode	Turn off the simulation mode as shown.
	Now let us compile the logic. The detailed steps on how to compile and save the logic are explained in the earlier tutorials.
Click on Settings >> Click on Microcontroller >> Select AVR ATmega16 40-PDIP Click on Settings >> Click on MCU parameters >> Change Crystal frequency to 16	Click on Settings and select the microcontroller AVR ATmega16 40-PDIP. Adjust its parameters as shown here.
Double-click on Xswitch in I/O list >> Select PC0 >> Click OK button Double-click on Xreset in I/O list >> Select PC0 >> Click OK button Double-click on YLED in I/O list >> Select PA0 >> Click OK button	Assign pin PC0 to Xswitch and PC1 to Xreset. Assign pin PA0 to YLED.
Click on Compile >> Click on Compile >> Go to Desktop/LDmicro folder >> Rename it as ‘timeron.hex’ >> Click on Save. Click OK button	Compile the logic as rto.hex.
Click on File >> Click on Save >> Go to Desktop/LDmicro folder >> Rename it as ‘rto.ld’ >> Click on Save	Save the ladder diagram as rto.ld.
	Now we will see the working of this logic on hardware.
Connect Mainboard to PC using USBasp laptop-usbasp.jpg Text box: Turn on the power supply	Connect the Mainboard to your laptop using USBasp. Turn on the power supply.
Open terminal >> Type cd Desktop/LDmicro >> Press ENTER >> type ‘avrdude -c usbasp -p m16 -U flash:w:rto.hex’ >> Press ENTER	Open the Terminal by pressing CTRL+ALT+T keys simultaneously. Go to the folder where you have saved the hex file. Type the command as shown to upload the hex file to the Mainboard.
Remove the USBasp connection from the laptop.	Turn off the power supply. Remove the USBasp connection from the laptop. This will prevent any hardware damage.
rto.png	Let us see the connection details now.
rto.png which shows all the connections as per the narration	Connect GND pin of the red LED of Traffic Light module to GND of the Mainboard. Then connect the +5V pin of the red LED to PA0 pin of the Mainboard.
rto.png which shows all the connections as per the narration	Connect GND and 5V of Switchboard to GND and 5V of the Mainboard respectively. Connect NO1 to PC0 of the Mainboard. Then, connect NO2 to PC1 of the Mainboard. Make the connections as shown in the picture.
Turn on the power supply.	After making all the connections properly, turn on the power supply.
Point to red LED	Initially the red LED will not glow.
Press the switch NO1 for 5 seconds	Press the switch NO1. Remember NO1 should be pressed for at least 5s for LED to turn ON.
Red LED glows.	The red LED should turn ON 5s after the NO1 is pressed.
Release the switch NO1	Once we release the NO1 it doesn't turn off the red LED.
Release the switch NO2	For that we need to press the switch NO2.
	Thus, an RTO timer retains the accumulated value even after the switch is released.
Turn off the power supply	Turn off the power supply.
	This brings us to the end of this tutorial. Let us summarize.
Slide 5: Summary Retentive Delayed turn ON (RTO) timer	In this tutorial we’ll learnt about working of Retentive Delayed turn ON timer
Slide 6: Evaluation 1. RES instruction is used with: RTO timer TON timer TOFF timer all of these 2. An RTO timer retains the present accumulated value when the rung goes false* True False 3. What timer instruction would be best suited for the below process? Track the time to make a product. It needs to track even if the process is halted and then started again.* TON TOFF RTO	Here are some self assessment questions for you. 1. RES instruction is used with_______ The options are RTO timer TON timer TOFF timer all of these 2. An RTO timer retains the present accumulated value when the rung goes false True or False 3. What timer instruction would be best suited for the below process? Track the time to make a product. It needs to track even if the process is halted and then started again. The options are: TON TOFF RTO
Slide 7: Answers to Assignment RTO timer True RTO	Now let us look at the answers. The answer to the first question is RTO timer The answer to the second question is true. The answer to the third question is RTO.
Slide 8:About Spoken Tutorial project	The video at the following link summarises the Spoken Tutorial project. Please download and watch it
Slide 9: Spoken Tutorial workshops	The Spoken Tutorial Project team: conducts workshops using spoken tutorials and gives certificates on passing online tests. For more details, please write to us
Slide 10: Forum for specific questions:	Please post your timed queries in this forum.
Slide 11: Forum for specific questions:	Do you have any general / technical questions on OpenPLC? Please visit the FOSSEE forum and post your question.
Slide 12: Acknowledgement	Spoken Tutorial Project is funded by MHRD, Government of India.
Slide 13: Thank you slide	This tutorial has been contributed by FOSSEE and Spoken Tutorial Project, IIT Bombay. And this is Harsha Priyanka from FOSSEE team, signing off. Thanks for watching.

Contributors and Content Editors

Nancyvarkey, Nirmala Venkat