Difference between revisions of "GIMP/C2/The-Curves-Tool/English-timed"

|Welcome to the spoken tutorial of Meet The GIMP.

| My name is Rolf steinort and I am recording this is Bremen, Northen Germany.  

|Now lets start with today's tutorial.

|It about curves.

| Let me 1st activate the Curves tool in the tool box and then click in the image.  

| You can see there is a histogram in the Curves tool and here are 2 bars with a gray scale.  

|Then there are some buttons to select in the curves tool like preview, save, open etc.

| But for now we’ll concentrate on the gray scale bar of Curve tool.  

|And in this bar we have some pixels which are really dark and some pixels which are really bright and in between there are pixels from dark to light.   

| This horizontal bar here consist of 256 different colour tone

|And for example this here 184 is gray.  

| This image consist lot of colours and I can show you the different colours here by changing the channel.

|  Let’s select red in the colour channel and you can see the red tones in the image.  

| Similarly you can change it to green and blue to get the respective tones.  

|And in this image it’s not very surprising that the green channel is dominant channel which has lot of values in it.

| Now click on reset channel.   

|And we have an area here where there are almost same number of pixels with this terminal and this terminal on the bar

|You go into the image when the curve tool is active and the mouse cursor changes to a little dropper, when I click here, the line in the histogram shifts to that point.  

|And this here is the output.  

|When I go up from mid gray to the translation curve , and then when I go to the vertical bar on left I hit again to mid gray   

|You see it here that the lower bar here is the original input and the vertical bar is the output of the curve tool.  

|I can change this curve in lot of different ways, which has nearly no limits.

|One limit is that I can’t pull the curve backwards and the moment I do that the point on the curve tool is lost.  

|But if I don’t want to see any bright pixels in the image, So I can pull all the points down and then the image is nearly black.   

|You can play around with the Curves tool until you get images that have been in fashion for years ago.  

|We can restart the curve by clicking on the reset button and get the original curve.  

|There are some more buttons in the curves tool like Linear Mode and Logarithmic Mode.  

|In logarithmic mode you get the smaller values pushed up.  

|Here in linear mode this line has double value from this line here.  

|In logarithmic mode this line can be 1, this 10, this 100 and this 1000.   

|Each step gives you 10 times more value and with this you see the small pixels which in linear mode are hidden

|you see it in this corner you can’t say if there are pixels which have value more than 250.

|But in logarithmic, you see we have pixels over the full range of the image.  

|Then here there is a button called Curve type, up to now I used the tool here where the curve gets the curve and when I change the curve type I can actually paint the curve and get some really funny stuff which I have never used till now.   

|Then there is save dialog and open dialog button.  

|When you finish with changing the curves you can save it for later use and recall it whenever you want to

|How do I use curve tool in this image.

|And to do this I think I will use the ‘S’ curve.  

|When I click OK the values of the curves is stored.

| There are no values in between here with no pixels and when I click on logarithmic mode, there also you can see no values for certain pixels.  

|Each time when you use curves tool, you lose some pixels in the image.   

|So don’t try to undo the curve operation by doing the opposite i.e by pulling the curve up here and pulling down here.

|Click OK and now you can see that it get worst and worst and you end in a image with colour banding.

|So use the curves tool only to make one change and use it with care otherwise you end up losing the pixels in the image and you get an image colour bandings in it.  

|If you want to send a comment, please write to info@meetthegimp.org and I would like to hear from you so leave comment on my blog.  

|This is Hemant Waidande dubbing for the Spoken Tutorial project.