Difference between revisions of "GIMP/C2/Adjusting-Colours-Using-Layers/English-timed"

{| border = 1

 

|'''Time'''

 

|'''Narration'''

 

 

| 00.22

| Welcome to Meet the Gimp. My name is Rolf Steinort and I’m recording this in Bremen, North Germany.  

 

 

| 00.29

|In the previous edition I got this image here after editing. And today I think I should do something to set the colors. Because this image is too green. There are lot of ways to adjust the color and one of them is the Curve Tool.  

 

| 00.47

|I click on the curves tool in tool box and then I select the green channel and pull the curve down. Now you can see that the colour channels and the fog in the image looks like the real fog.  

 

| 01.02

|Now, I have to adjust the curve in such a way that I get an image which is gray and not green or magenta.  

 

| 01.13

|I don’t want to use curves tool because it damages the details of the image and I can’t correct the damage afterwards, I could use the undo tool but I’ll have to redo all the steps after that. So I want to have something that’ll not damage the image and I can adjust later on.

 

|01.33

| There is such a way which uses a simple filter with layers. So I have open here the layer dialog. You’ll see here background which is our original image. And I simply add a new layer and I select white in Layer Fill Type and give it a name, color correction green.  

 

|01.59

|Now my image is fully white but I can change the layer mode. The layer mode is an algorithm which combines the two layers i.e the original background layer and the newly created layer. So I choose here the Multiply mode.  

 

| 02.22

|And you get the original image back as it was before. The Multiply mode, multiplies the pixels from the background to the pixels from the foreground, and divides the result by 255. And in a white picture all the color channels are 255, so multiplying by 255 and dividing by 255 gives the starting point i.e. background

 

 

| 02.52

| But if I reduce one channel in the new layer, it will be reduced in the background also because multiplying by say 200 and dividing by 255 gives less.

 

| 03.05

|Now i want to select such a color which has a reduced green channel.  

 

| 03.12

|Here I have black as foreground colour,which i change to background colour and white as foreground colour and you can see that red, green & blue all colour channels have same value i.e 255.  

 

 

| 03.30

| 03.50

| 04.10

|But  I can adjust the intensity of my green reduction with the help of the opacity slider. And when I go back to zero I get the old image, and when I pull the slider up I can reduce the green channel in the image and also avoid getting magenta into the image.  

 

 

| 04.35

| I think this looks quite good. By using the layers tool I can do changes anytime I want to and also I can do fine adjustments when more layers are stacked onto it and the change will stay even if I change something in underlying picture. There are still changes to be made in this layer as now it appears gray and I want to add a bit of blue.  

 

|05.03

|Again I follow the same procedure and make a new layer and called it color correction blue. And now I want to add a little bit of blue,

 

 

|05.15

|For adding blue in the image, I use the Screen mode which is a little bit more complicated than Multiply mode. In screen mode the colors are 1st inverted and then multiplied and divided and quite complicated.  

 

| 05.33

|Let me change the foreground colour to black and add the colour  i want to add directly and now I have to add a little bit of blue. So slide down the blue slider a bit. And drag the colour into the image. This here is supposed to be blue, which looks still like black but it is very dark blue. Look at the image here and when I switch this off here, you see the change. The image is definitely bluish.

 

| 06.08

|I can switch off both the new layers and by that you get the starting point. When I click on the 1st layer we see the reduced channel of green and when I click on 2nd layer it adds a bit blue colour.  

 

 

| 06.22

| I think this is too much blue so I reduce the opacity. I think this looks good. I can adjust it later on all the time.  

 

| 06.33

|The layer tool is very powerful because you can create layer upon layers and in each layer you can change the pixels which are coming up from the lower layer. Possibilities of doing the correction is limitless and you can do it when ever you want. Perhaps here you can slide the opacity slider a bit down to get a good colour and you can play with these sliders which will give real hand full of possibilities to change the color here.