View source for OpenFOAM/C2/Creating-curved-geometry-in-OpenFOAM/English

Tutorial: Creating curved geometry in OpenFOAM.


Script and Narration: Rahul Joshi


Keywords: Video tutorial, CFD, Flow over cylinder, edges, blocks.



{| style="border-spacing:0;"
| style="border-top:0.05pt solid #000000;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Visual Cue
| style="border:0.05pt solid #000000;padding:0.097cm;"| Narration

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 1
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Hello and welcome to the spoken tutorial on '''creating Curved geometry in OpenFOAM'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 2 : Learning Objectives
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In this tutorial I will show you steps for creating a '''curved geometry in OpenFOAM'''.


Viewing the results in '''ParaView'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 3: 

System Requirement 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| To record this tutorial I am using 
*'''Linux Operating system Ubuntu version 10.04'''. 
*'''OpenFOAM version 2.1.0 '''
*'''ParaView version 3.12.0 '''

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 4: System Requirement 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| The tutorials were recorded using the versions specified in previous slide.

Subsequently the tutorials were edited to latest versions.

To install latest system requirements go to Installation Sheet.

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 5:


Hover over cylinder


Hover over the geometry


Hover over blocks


break the circle into 4 parts
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| We will create a '''geometry''' for '''flow over cylinder'''.


Note that I am using this '''case''' just for explanation.


The '''cylinder '''is in a form of a semi circle.


'''Meshing''' is a '''body fitted grid'''.


The entire '''geometry''' is divided into '''blocks'''.


We break the semi circle into equal number of '''parts'''.


Now minimise this.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Open the lid driven cavity blockMeshDict file


Hover over arcs
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Open the '''blockMeshDict '''file of the previous tutorial.


I have already opened it.


Scroll down, for '''simple geometries''' you can see that '''edges '''is kept empty.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now create a new '''blockMeshDict''' file.


To do this let us minimise this first.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| On the desktop


Right click > create document >create file
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now '''right click > Create document > Empty file'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Name this as blockMeshDict
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Name this as '''blockMeshDict'''.


Note that '''M''' and '''D''' here are capital.


Open this.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Copy the blockMeshDict of '''Lid driven cavity''' file from line 0 to line '''convert to meters'''
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now you can copy the initial few lines from the '''lid driven cavity''' upto '''convertTometers'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Copy these lines
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Go up copy this upto '''convertToMeters'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Paste in the new blockMeshDict file
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Copy this and paste it in the new '''blockMeshDict file'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Change the geometry to point one to one
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Change the '''convert to meters''' from '''point one''' to '''one'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Geometry is in meters 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| As our '''geometry''' is in '''meters''' we will keep this as '''one'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Press enter
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now press '''Enter'''. 


Press '''Enter''' again.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Refer to the figure of flow over cylinder in slide 4



| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| After this you need to enter the '''co-ordinates''' of the''' geometry''' in '''vertices'''.

Let me switch back to the slides.

Note that the '''points''' should be ordered in such a way starting from '''0,1,2,3''' and so on, as shown in the figure.

Minimize the slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type vertices after convertTometers
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now type '''vertices''' in the '''blockMeshDict file''' and press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Insert an '''open bracket'''.


Press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Enter the co-ordinates as shown in the diagram
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now enter the '''co-ordinates''' of '''points''' as shown in the '''diagram'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Let me switch back to the slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Refer to the next slide for half semi-circle
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| For explanation I will use the right half of the semi-circle.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| current blockMeshDict file
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter the values for the points in the figure starting from '''zero'''.


Let me switch back to the '''blockMeshDict file'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space and enter the '''co-ordinates''' of '''point 0'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 0 - Insert (0.5 0 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| '''Open close bracket''' and enter '''(0.5 (space) 0 (space) 0)'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Again leave some space, '''open close bracket'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 1- Insert (1 0 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter '''co-ordinates''' for '''point 1 (1 (space) 0 (space) 0)'''


Press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave two '''vertical spaces''',  again press '''Enter'''.


Again press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space and enter '''co-ordinates '''for the '''point number 4'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 4 – Insert (0.707 0.707 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| '''Open close bracket''', enter '''(0.707 (space) 0.707 (space) 0)'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Press '''Enter'''.


Leave some space.


'''Open close bracket'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 5 -Insert (0.353 0.353 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter the '''co-ordinates''' for '''point 5'''.


Enter '''(0.353 (space) 0.353 (space) 0)''', press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now leave 4 vertical spaces.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter '''co-ordinates''' for '''point number 9'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Vertical spaces
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| '''1 2 3 4 ,''' again press '''Enter'''.


Leave some space.


'''Open close bracket.'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 9 – Insert (0 1 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter '''(0 (space) 1 (space) 0)''', press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space.


Enter the '''co-ordinates''' for '''point number 10'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Point 10 -Insert (0 0.5 0)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Open close bracket''' (0 (space) 0.5 (space) 0)''', press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Remaining part of the semi-circle 


use the same procedure
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Similarly enter the '''co-ordinates''' for remaining '''points''' in the '''geometry.'''


Insert a '''close bracket''' and put a''' semi-colon '''


Press '''Enter'''.


Again press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| In blockMeshDict file type blocks
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now type '''blocks''' and press '''Enter'''.


Insert an '''open bracket''' and press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Let me switch back to the slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide showing blocks
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| '''Block numbers''' are circled as shown in the figure.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now let me switch back to the '''blockMeshDict file'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Enter the type of block here
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space.


Enter the type of the '''block''' that is '''hex'''


Leave some space.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Enter points for blocks
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now enter the''' points''' for the '''blocks'''.


'''Open close brackets'''

Leave some space.


'''Open close brackets'''

Leave some space.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| SimpleGrading (1 1 1)
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| This '''simple grading''' can be kept as '''(1 1 1) ''' and press '''Enter'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Refer to the previous tutorial on simple geometry in openfoam
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| For creating the '''blocks''' please refer to the '''tutorial''' on '''Creating simple geometry in OpenFOAM'''.


Note that there will be more number of '''blocks''' in this example.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Insert close bracket and 


semi-colon



| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now insert a '''close bracket'''.


Insert a '''semi-colon''' and press '''Enter'''.


Again press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type edges
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In the next line, type '''edges''' and press '''Enter'''.


Insert an '''open bracket''' and press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Here you need to enter the '''points''' which are the '''end points''' of the '''arc'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Enter the arc points 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space and type '''arc''' and leave some space.


Type the '''points''' which are the '''end points''' of the '''arc'''.

Let me switch back to the slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Insert '''end points''' of the '''arc'''


From this slide



| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In this insert the '''end points''' of the '''arc'''.


We start with '''0 5'''.


Let me switch back to the '''blockMeshDict file'''.


Enter''' 0 space 5'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Leave some space.


Insert '''open close bracket'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In '''brackets''' enter the '''co-ordinate''' of any '''intermediate point '''in between the two '''arc points'''.


Now let me switch back again to slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 6: for arcs
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In the figure you can see that you have to pick up a '''point''' in between the two '''points''' of the '''arc'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In this '''geometry''' I have picked up right half of the circle.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide showing trignometric relations

Sin(theta) and cos(theta) relations
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Using '''simple geometric relations''', you can find the '''co-ordinates''' of the '''intermediate point''' shown in the semi-circle.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Repeat the above procedure for the remaining semi-circle 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Similarly you can repeat the procedure for rest of the semi-circle '''geometry'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now let me switch back to the '''blockMeshDict file'''.


Now press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Note that there are more number of '''arcs''' in this example.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Insert a '''close bracket'''.


Insert a '''semi -colon''' and press '''Enter'''.


Again press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| In the next line after arcs


refer to the tutorial on creating simple geometry in openfoam
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter the '''boundary patches''' after '''arcs'''.


Refer to the tutorial on '''Simple geometry in OpenFOAM''' for entering the '''boundary patches'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Enter boundary
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Enter '''boundary''', press '''Enter'''.


Insert '''open-close bracket''', press '''Enter'''.

Insert '''close bracket semi-colon''', press '''Enter'''.


Again press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type mergePatchPairs


P here is capital
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now, in the next line type '''mergePatchPairs'''.


Note that '''P''' here is capital.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Press '''Enter'''.


Insert an '''open bracket''' and press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Since there are no '''patches''' to be merged, this can be kept empty.


Insert a '''close bracket'''.


Insert a '''semi -colon '''and press '''Enter'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 7 : 


Points for the front face in the geometry



| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Let me switch back to the slides.


Similarly enter the '''co-ordinate points''' for the '''points''' in the '''front face''' of unit thickness of the '''geometry''', as shown in the figure.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Press Ctrl+Alt+t keys 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Open a '''Command terminal'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type '''run''' and press '''Enter'''.

'''cd tutorials''' and press '''Enter'''

'''cd basic''' and press '''Enter'''

'''cd potentialFoam''' and press '''Enter'''

cd cylinder and press enter
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In the '''command terminal''' type the path for your '''case'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| I have already set the path for the '''tutorial case''' of '''flow over cylinder'''

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type blockMesh and press enter
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In the '''terminal''' type '''blockMesh '''for '''meshing''' the '''geometry''' and press '''Enter'''.


'''Meshing''' is done.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 8: For OpenFOAM v 5.0
To open '''cylinder case directory''', type the following in your '''run folder''':

'''$cd tutorials/basic/potentialFoam/cylinder'''


To '''run Allrun script file''', type: '''$./Allrun'''


This will '''run blockMesh''' and '''potentialFoam commands'''.

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| 

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Type paraFoam and press enter
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now type '''paraFoam''' in the '''terminal''' and press '''Enter''' to view the '''geometry'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Let me drag this to the '''capture area'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| In the object inspector menu click APPLY button
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Now on the left side of '''object inspector menu''' click '''Apply'''.


The '''geometry'''  will be created as seen in the '''ParaView''' window.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Scroll down the '''Object inspector menu'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Check and uncheck the mesh field box
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Check and uncheck the '''Mesh field box'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Demo
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| You can see different '''regions''' of the '''geometry'''.


You can also see the''' wire frame '''of the '''geometry'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| For '''wireframe''' of the geometry


Change from surface to wireframe
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| On top of '''active variable control menu''' in the drop down menu, change from '''Surface''' to '''Wireframe'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| 
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| You can see the '''wireframe model''' of the '''geometry'''.


Close this.


Let me switch back to the slides.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 9: Summary
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| In this tutorial we learnt:

*How to '''create a curved geometry'''.
*How to '''enter points''' for '''edges''' in '''OpenFOAM'''


This brings us to the end of the tutorial

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 10: Assignment
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| As an assignment, create a '''geometry''' with 
*'''inner semi-circle of radius 2 meters'''
*and '''outer circle of radius 4 meters'''


and view the results in '''ParaView'''.

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 11:

About Spoken tutorials
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Watch the video available at this URL:

http://spoken-tutorial.org/What_is_a_Spoken_Tutorial 

It summarizes the Spoken Tutorial project. 

If you do not have good bandwidth, you can download and watch it. 

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 12: 

About Spoken Tutorials
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| The Spoken Tutorial Project Team

-Conducts workshops using spoken tutorials

-Gives certificates to those who pass an online test

-For more details, please write to contact@spoken-tutorial.com

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 13 : Forum to answer questions
Do you have questions on THIS Spoken Tutorial?
Choose the minute and second where you have the question
Explain your question briefly
Someone from the FOSSEE team will answer them. Please visit
http://forums.spoken-tutorial.org/
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| 

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 14 : Forum to answer questions
Questions not related to the Spoken Tutorial?
Do you have general/technical questions on the Software?
Please visit the FOSSEE forum
http://forums.fossee.in/
Choose the Software and post your question
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| 

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 15 : Lab Migration project
We coordinate migration from commercial CFD software like ANSYS to OpenFOAM
We conduct free Workshops and provide solutions to CFD Problem Statements in OpenFOAM
For more details visit this site:
http://cfd.fossee.in/
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| 

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 16 : Case Study project
We invite students to solve a feasible CFD problem statement of reasonable complexity using OpenFOAM
We give honorarium and certificate to those who do this
For more details visit this site:
http://cfd.fossee.in/
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| 

|-

| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| Slide 17 :

Acknowledgement
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| Spoken Tutorials are part of Talk to a Teacher project, 

It is supported by the National Mission on Education through ICT, MHRD, Government of India. 

More information on the same is available at the following URL link http://spoken-tutorial.org/NMEICT-Intro

|-
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:none;padding:0.097cm;"| About the contributor
| style="border-top:none;border-bottom:0.05pt solid #000000;border-left:0.05pt solid #000000;border-right:0.05pt solid #000000;padding:0.097cm;"| This is Rahul Joshi from IIT BOMBAY signing off. Thanks for joining

|}